Numero immagine 32 della sezione corrente di Zeeduin Facade di Cosentino Italia

Zeeduin Facade

Cosentino Flagship Project

Ultra-thin façade cladding gives Zeeduin a slightly floating effect

By Ignace Deconinck

Numero immagine 33 della sezione corrente di Zeeduin Facade di Cosentino Italia

Sede

Nieuwpoort, Belgium

Materiale

Dekton

Colore

Nayla

Quantità

462 m2

Architect / Designer

Ignace Deconinck

Applicazione

Facciata ventilata

Spessore

4 mm

Dekton, insulation, aesthetics and durability for facades

The Zeeduin renovation project is situated on the corner of Franslaan with Lefebvrestraat in Nieuwpoort. After a few decades, the façades - covered with relatively thin prefab silex concrete elements - showed concrete damage due to carbonation. The client and architect opted for a total renovation for the façades, with 4 mm thick Dekton Slim plates by Cosentino, glued on a ventilated aluminium support structure.

The apartment building dates back to the 1970s and has 6 above-ground floors. The gallery terraces, made of in situ concrete with the floor slab running from the inside to the outside without thermal interruption, were fitted with a mortar-bed tiling. Water penetration caused concrete damage and general degradation of the concrete coating. The absence of façade and roof insulation also contributed to a total renovation.

Dekton Slim, 4mm full of possibilities

A light façade cladding had to give the building a new, sleek and contemporary zest. This resulted in the choice of Dekton Slim plates (with a thickness of 4 mm), glued to an aluminium carrier. “This way the façade could be insulated to a maximum without bringing the façade surface too far forward,” according to the architectural engineer Ignace Deconinck of the eponymous Architecten Expertisebureau from Veurne.

A small balcony construction with a walking zone was provided for the apartments on the façade corner - with in the original condition only a balustrade in the façade surface. Not evident from a technical point of view. Good coordination (including dimensions and planning) between the main contractor (Aquastra), the balustrades subcontractor (Aluform) and the façade cladding subcontractor (Murex Stone) was required. After concrete repair, the gallery terraces were fitted with a new reinforced terrace compaction system and glass balustrades with front mounting of the uprights.

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

"Dekton delivers high-quality and a great technical performance compared to other existing surfaces"
Stephanie Bevernagie

Stephanie Bevernagie

Cosentino Belgium

Nayla, an off-white full of nuances

The architect opted for a dark-coloured base (the ground floor) and a light superstructure to give the floors a more floating effect. “For the ground floor, we opted for a coating in fired blue bluestone, a good match with the small grey speckles, the white mass of the Nayla type and the terrace floors in a grey tone,” says Deconinck about the choice for the Dekton colour “Nayla” (white speckled).

“Thanks to its properties, Dekton delivers high-quality, technical performance compared to other existing surfaces: highly scratch-resistant, frost-resistant and thaw-resistant, and resistant to salty air and UV rays. Colour stability, dimensional stability and pressure resistance are high. With a fire reaction class A2, s1-d0, Dekton can even be used for tall buildings,” says Stephanie Bevernagie of Cosentino.

Materiali Cosentino utilizzati in questo progetto

Nayla-detail-1

Nayla

Dekton
Numero immagine 57 della sezione corrente di Zeeduin Facade di Cosentino Italia

Vuoi conoscere le soluzioni di Dekton per le facciate?

Numero immagine 58 della sezione corrente di Nippon Express di Cosentino Italia

Nippon Express

Case Study

Dekton makes a first impression to remember

By Harris Architects

Numero immagine 59 della sezione corrente di Nippon Express di Cosentino Italia

Sede

Itasca, IL, USA

Materiale

Dekton

Colore

Bergen

Quantità

1000 sq.ft

Architettura / Progetto

Harris Architects

Applicazione

Rivestimenti

Installare

Stone Systems of Chicago

Spessore

4 mm

The perfect material for a bold vision

Nothing makes a statement like a large wall cladded in Dekton, and that’s exactly what we see at Nippon Express’ Itasca offices. Kasey Kluxdal, Senior Design Architect for Harris Architects had a vision in mind and presented the Cosentino team with a Computer-Aided Design (CAD) and together they explored the many Dekton colors, textures, and thicknesses that could bring her vision to life.

The decision was clear, Dekton Bergen was the perfect color for Nippon Express’ reception area. From the Stonika Collection, Dekton Bergen is inspired by natural Portobello marble with beautiful grayish veins creating sculptural patterns on an off-white base. With its high-gloss print, 4 mm thickness, and large panels, Dekton Bergen transformed the reception area of this global Japanese logistics company.

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

“The architect fell in love with Dekton Bergen and was impressed with the large format look. This was the key to making the project a success”
Maritza Parada Arias

Maritza Parada Arias

Business Manager, Stone Systems

The magic is in the bookmatch

When cladding this two-story wall, it was imperative that the bookmatch be perfect. Cosentino and the installer, Stone Systems of Chicago, worked hand-in-hand to bookmatch the large Dekton panels to create a seamless statement wall in the reception area and behind the two-story stairwell. Dekton’s large-format panels and tight grout joints also greatly contribute to the visually continuous aesthetic of the wall and the thin 4 mm thickness allows the wall area to be as narrow as possible.

This logistic giant’s Itasca office is as unique as it is unforgettable. Dekton Bergen adorns the walls and is the first thing people see when they step inside - talk about making a good first impression.

Numero immagine 67 della sezione corrente di Nippon Express di Cosentino Italia

Materiali Cosentino utilizzati in questo progetto

Bergen-Swatch-1

Bergen

Dekton

Casi di studio correlati

Numero immagine 83 della sezione corrente di Nippon Express di Cosentino Italia

Vuoi conoscere le soluzioni di Dekton per le facciate?

Numero immagine 84 della sezione corrente di Via Paleocapa Facade di Cosentino Italia

Via Paleocapa Facade

Flagship Project

Dekton fornisce una soluzione ai problemi strutturali di questa facciata italiana

Di Duesse Hi Tech

Numero immagine 85 della sezione corrente di Via Paleocapa Facade di Cosentino Italia

Sede

Bergamo, Italia

Materiale

Dekton

Colore

Entzo

Quantità

158 m2

Architettura / Progetto

Duesse Hi Tech

Applicazione

Facciata ventilata

Data di fine

2021

Spessore

12 mm

Punto di partenza: una facciata in pietra naturale che presentava alcune problematiche

Nel 2021 è stato completato con successo il restauro parziale di un edificio situato a Bergamo, in Italia, in via Paleocapa 3. Il lavoro consisteva nella sostituzione della facciata ventilata esistente, che aveva solo 15 anni, con una più leggera e altrettanto bella.

Quando il team Duesse Hi Tech ha assunto la gestione del progetto, si è trovato di fronte a un edificio con un serio rischio di crollo a causa del peso dei 250 m2 di pietra naturale (probabilmente Calacatta di origine nazionale) utilizzata per la facciata. Inoltre, al piano terra, progettato come un portico sorretto su pilastri, il team ha rilevato una depressione di 5 cm causata dal carico statico. Il rischio riguardava l’edificio stesso e i pedoni (essendo situato in una strada molto trafficata di Bergamo) e richiedeva un’azione rapida.

Oltre all’eccesso di peso della pietra naturale, era evidente la presenza di un problema tecnico con il sistema di ancoraggio della facciata ventilata, progettato in modo errato in termini di capacità statica del cuscinetto di carico. Nel corso del restauro, sono state utilizzate lastre Dekton Entzo da 12 mm per sostituire la pietra naturale, riducendo significativamente il peso a circa 50 kg per unità su ciascuna delle pareti dell’edificio.

Considerando l’urgenza di sostituire la facciata, Dekton era l’opzione migliore. Il nuovo design, l’installazione della sottostruttura e dello strato isolante e l’intero rivestimento sono stati completati in sole due settimane da un team di tre persone.

Numero immagine 95 della sezione corrente di Via Paleocapa Facade di Cosentino Italia

Soluzione: Tecnologia Dekton senza compromettere la bellezza

Dopo aver risolto le sfide tecniche, è stato necessario trovare un materiale bello da vedere come la pietra naturale e con una finitura simile alla Calacatta. L’ampia gamma di colori Dekton ha permesso di trovare la finitura più vicina al rivestimento originale: Entzo. Il risultato è lo stesso effetto cromatico e “naturale” della pietra richiesto dalle autorità comunali e provinciali per le aree di interesse storico.

In breve, le facciate ventilate Dekton sono perfette sia per la ristrutturazione del rivestimento esistente che per nuovi progetti. Cinque proprietà fanno di Dekton la soluzione perfetta per le facciate ventilate: 1. Leggerezza; 2. Lastre nel grande formato (formato Jumbo 325 x 159 cm); 3. Installazione rapida; 4. Aspetto naturale; 5. Elevate prestazioni statiche e architettoniche.

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

“Dekton è l’unico materiale sintetico con un aspetto quasi identico alla pietra naturale. È perfetto per gli edifici elencati”
Duesse Hi Tech

Duesse Hi Tech

Materiali Cosentino utilizzati in questo progetto

Entzo-Detalle-2

Entzo

Dekton

Progetti di punta correlati

Numero immagine 111 della sezione corrente di Via Paleocapa Facade di Cosentino Italia

Vuoi conoscere le soluzioni di Dekton per le facciate?

Numero immagine 112 della sezione corrente di Lakeside Bank di Cosentino Italia

Lakeside Bank

Case Study

The technical challenge of a façade designed to impress

By Pappageorge Haymes Ltd.

Numero immagine 113 della sezione corrente di Lakeside Bank di Cosentino Italia

Sede

Illinois, United States

Materiale

Dekton

Colore

Zenith

Quantità

465 m2

Architettura / Progetto

Pappageorge Haymes Ltd.

Applicazione

Rainscreen façade (concealed fastening)

Collaborator | Allestitore

International Contracts Inc (ICI) |Stone Systems of Chicago

Spessore

12 mm

Cosentino team, coordination at all stages of the project

Lakeside is a well-known commercial bank in the Chicago area, Illinois. As part of the refurbishment process of some of their offices, specifically the Oakbrook Terrace office, they hired the services of the architectural studio Pappageorge Haymes Ltd. From the very beginning, the studio planned a modern, interesting façade that would catch the eye of passers-by, inviting them to look at it.

The execution of a stunning façade required a high quality material. Pappageorge had worked with natural stone in the past, but problems always arose because of its poor UV resistance and technical limitations. The studio had heard about the technical properties of Dekton on exterior façades and was keen to learn more.

The Cosentino team met with Pappageorge architects, provided material samples and designed a mock-up featuring the XL 45 system. In this rainscreen system, aluminum rails are anchored to the back of the Dekton slab by horizontal grooves. In the end, Dekton was the material of choice for the versatility it offered in such a complex project. Stone Systems of Chicago, a certified fitter knowledgeable of the material, was in charge of the execution of the project.

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

“It took us more than a year to overcome all the technical complexities of this 3D façade. Now, looking at the result, I can say that every minute was worth it”
Maritza Parada Arias

Maritza Parada Arias

Business Manager, Stone Systems of Chicago

The monolithic white of Dekton Zenith

After a difficult but very beautiful job under the direction of architect Donald Mouch, the Lakeside Bank façade is now one of the most impressive façades in Oakbrook Terrace, and the most beautiful ever executed by Stone Systems.

Without detracting from the flawless technical execution, a large part of the success is due to the beauty of the material. Dekton Zenith is part of the Solid Collection. Its near-perfect Nordic white blends excellently with the red brick used on the rest of the Lakeside Bank building, in a balanced mix of modernity and classicism.

A premium material for a first class institution: the Lakeside Bank has undoubtedly found its perfect match in Dekton. Dekton’s superior technical properties coupled with design aspects such as elegance, sobriety and perfection, make the Oakbrook Terrace building the most prominent of all Lakeside Bank buildings.

Materiali Cosentino utilizzati in questo progetto

Zenith-dekton-1

Zenith

Dekton

Progetti di punta correlati

Numero immagine 141 della sezione corrente di Lakeside Bank di Cosentino Italia

Vuoi conoscere le soluzioni di Dekton per le facciate?

Numero immagine 142 della sezione corrente di Cosentino Center Zurich di Cosentino Italia

Cosentino Center Zurich

Case Study

Harmonious contrast

Pizrog Natursteine AG

Numero immagine 143 della sezione corrente di Cosentino Center Zurich di Cosentino Italia

Sede

Neuhaus, Switzerland

Materiale

Dekton

Colore

Danae

Applicazione

Facciata ventilata

Architettura / Progetto

Pizrog Natursteine AG

Data di fine

2021

Spessore

12 mm

Façade combines light Dekton Danae with dark natural slate

When José Luis Moral takes off, the world lies at his feet. The fervent sports pilot climbs over the meadows and wooded hills north of Lake Zurich and looks out over a breathtaking Alpine panorama. The snow-covered mountains glitter above, as does the lake below. Moral has been installing surfaces for individual construction projects of his customers for around 30 years on its banks and far beyond. With Roandi Immobilien AG he has become one of the developers himself.

His down-to-earth attitude also benefits him here. This way Moral was able to find optimally located logistical locations in a very attractive region, both scenically and commercially, not only for Pizrog Natursteine AG, which he is the head of, but also for an important business partner. The main user in Neuhaus became the “Cosentino Center Zurich” with 375 sq m of exhibition and office space and 2,325 sq m of storage space. The specialist for individual processing and the laying of stone surfaces moved with his company to Bubikon, which is 15 km away.

Numero immagine 145 della sezione corrente di Cosentino Center Zurich di Cosentino Italia

Aesthetic and functional

“We planned and realized the two buildings in parallel with a local architectural office. This is how it always work best on site,” says José Luis Moral. At the same time, he set uniform guidelines. “Character-rich design is very important to me, as well as outstanding functionality and sustainable quality for all Roandi items.” This applies in particular to the building envelope. The back-ventilated curtain façade has proven to be particularly effective here. It permanently combines high energy efficiency with extensive design freedom.

“The façade front should be invitingly bright and radiate a light Mediterranean warmth, an impression that is reinforced by the contrasting dark warehouse in the background,” explains José Luis Moral. “The selected materials should naturally embody the highest standards of quality and the proverbial Swiss precision. I think we succeeded in this through the combination of Dekton Danae and natural shale. By the way, both materials come from Spain just like me,” adds Moral with a wink.

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Ultra-compact surface

Natural minerals, pressure and heat created the two surfaces used. However, it can take millions of years for the clay sediment to become shale. With Dekton by Cosentino the metamorphosis happens in a controlled and accelerated manner within a few hours. At 25,000 tons of pressure and 1200°C the minerals are formed into an ultra-compact surface using particle sinter technology (PST). Dekton is resistant to cold, heat and thermal shocks, UV and color-fast. The material can therefore be used both inside and outside.

Dekton is produced in large-format panels of up to 320 cm x 144 cm and in over 50 designs and textures. In the Roandi projects, the sandy shade Dekton Danae from the Natural Collection in 1.2 cm thickness was used. An embedded glass fiber mesh ensures that no fragments can come loose if the façade is damaged. Cosentino delivered the plates that measure up to 160 x 110 cm cut to size, slotted at the top and bottom and with processed edges, directly to the construction site – numbered consecutively and “just in time”.

Numero immagine 146 della sezione corrente di Cosentino Center Zurich di Cosentino Italia

Shimmering monolith

The substructure for the outer cladding consists of thermally separated aluminum brackets, which are fastened with bolt anchors to the concrete wall, otherwise insulated with 19 cm stone wool. Vertical L-profiles are attached to the supporting brackets with horizontal double T-rails. The top and bottom slotted Dekton plates were inserted into these and securely fixed on site by the Pizrog Natursteine AG installers. “With this system you work very quickly and at the same time with high precision”, says Moral.

Since Dekton only has a negligibly low thermal expansion coefficient the spaces between the individual plates can be very small. “While large window areas allow plenty of daylight inside the opaque part of the building envelope has a softly shimmering monolithic character this way”, says a satisfied José Luis Moral. He will soon be building again with Roandi. Another large commercial building is being built right next to the “Cosentino Center Zürich” - naturally again in the proven combination with Dekton Danae.

Numero immagine 147 della sezione corrente di Cosentino Center Zurich di Cosentino Italia

Materiali Cosentino utilizzati in questo progetto

danae-dekton-1

Danae

Dekton
Numero immagine 161 della sezione corrente di Cosentino Center Zurich di Cosentino Italia

Vuoi conoscere le soluzioni di Dekton per le facciate?

Numero immagine 162 della sezione corrente di Liderim offices di Cosentino Italia

Liderim offices

Case Study

Liderim, the office reimagined in a cosy space

By Eli Hacohen

Numero immagine 163 della sezione corrente di Liderim offices di Cosentino Italia

Sede

Tel Aviv, Israele

Materiale

Dekton

Colore

Aura

Data di fine

2021

Architettura / Progetto

Eli Hacohen | A. Weiss (developer)

Applicazione

Ventilated façade on walls and ceiling | Cladding of reception desk and tables

Spessore

8mm and 12mm

The visual impact of large format Dekton

The new Liderim offices in Tel Aviv (Israel) exude elegance. Once in the reception area, there is an impressive desk made from a huge, seamless, large-format Dekton Aura slab. The effect is overwhelming, thanks to the use of the same material for the wall and ceiling cladding. The overall feeling is one of understated luxury, combining a material such as Dekton Aura, inspired by classic marble, with cement flooring and wood.

The desk has been created from several planes with a sought-after asymmetry, giving it movement and modernity, in contrast to the classic look of the finish itself. Dekton Aura, a colour from the Natural Collection, with grey to beige veining reminiscent of Calacatta and Carrara marble, contributes to this.

When the architect responsible for the project, Eli Hacohen, was asked why he chose Dekton Aura, the answer was clear: ‘I chose Dekton Aura for the Liderim offices because I wanted to convey understated luxury, and because of the versatility of the material for application as wall, ceiling and furniture cladding.’

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

‘The Cosentino team is very customer-oriented. They have helped us to select the material and have supported us until the final execution of the project.’
Eli Hacohen

Eli Hacohen

Architetto

Dekton, interior design down to the last millimetre

In the Liderim offices, everything is designed to create a welcoming atmosphere that invites employees and visitors to stay. To this end, the exterior features are integrated into the interior of the building, providing continuous visual communication, especially in the entrance, reception area and meeting rooms.

Everything has been controlled and meticulously executed. Nothing has been left to chance. Not surprisingly, the roof cutting and the wall cladding also required a great deal of precision and detailed planning. This was perhaps the main challenge of the project, which Hacohen successfully overcame thanks to the Cosentino team, which is always ready to provide technical solutions.

The choice of the same material, Dekton Aura, for the tables in the meeting rooms has been another success of the project. In addition to creating a cosy space, in combination with the beige leather chairs, the material connects with the reception area of the offices, strengthening the original creative concept. Dekton is also available in a thickness of only 4mm in its Slim version, which offers multiple possibilities as furniture cladding – table tops, cabinet fronts, and one-piece items such as side tables – without the disadvantages of natural stone, which is highly susceptible to scratches, liquids or sunlight exposure.

A well-designed LED lighting system, plant materials in the right places and plenty of natural light complete the final look.

Numero immagine 169 della sezione corrente di Liderim offices di Cosentino Italia

Materiali Cosentino utilizzati in questo progetto

aura_dekton-1-2

Aura

Dekton

Casi di studio correlati

Numero immagine 185 della sezione corrente di Liderim offices di Cosentino Italia

Vuoi conoscere le soluzioni di Dekton per le facciate?

Numero immagine 186 della sezione corrente di Vitanya Tower di Cosentino Italia

Vitanya Tower

Case Study

Dekton Slim, versatile look for Vitania Tower in Tel Aviv

By Alex Meitlis Architects

Numero immagine 187 della sezione corrente di Vitanya Tower di Cosentino Italia

Sede

Tel Aviv, Israele

Materiale

Dekton

Colore

Soke

Quantità

2000 m2

Architettura / Progetto

Alex Meitlis Architects | Nielsen (collaborator) | Vitania (developer)

Applicazione

Interior wall and door cladding

Data di fine

2021

Spessore

4mm

The lightness of Dekton, the aesthetics of concrete

In the Vitania skyscraper in Tel Aviv, which houses a showroom for Mazda and Ford cars, a new part has been added to the office area. The building boasts a multi-storey atrium with a huge multimedia screen, which overlooks the street and occupies the full height of the space.

For the cladding of this new part, the idea was to use a material suitable for working with large, thin slabs. It also had to be aesthetically pleasing and blend in well with the concrete finish of the rest of the tower.

Therefore, the material chosen was Dekton Slim in Soke colour, with an ultra-thin thickness of 4mm. This colour is part of the Industrial Collection and is inspired by classic cement, perfect for the modern finish that the architect wanted to achieve.

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

"It was wonderful to be able to visit the factory and see all the colors in large size"
Elad Cohen

Elad Cohen

Alex Meitlis Architects

A skyscraper with a focus on sustainability

Vitania is an office tower situated in Tel Aviv, Israel. With its 17 storeys and 19,500m2 built above ground – plus 3 storeys of parking below ground level – it rises majestically above a beautiful green area. Not surprisingly, the tower meets the strictest technical specifications and sustainability criteria to save energy and money, challenges that the BREEM-certified Dekton has helped to overcome.

Visually, the building has a luxurious lobby and offers its users the possibility to configure the office according to their needs. The building is attractive for its simplicity, achieved in part by the use of concrete and clean, straight lines. In the new part, the walls, floors and doors of the lobby were clad with Dekton, achieving greater uniformity. ‘The building itself is a contemporary building and the desire was to convey modernity and cleanliness, both in the main lobby and throughout the floor. The colour we chose (Soke) perfectly matches the experience we were looking for,’ explains Elad Cohen, architect at Alex Meitlis Architecture and Design.

In addition, as a certified fire-resistant material, Dekton helped to provide the extra safety required for a colossal building such as the Vitania Tower.

Numero immagine 191 della sezione corrente di Vitanya Tower di Cosentino Italia

Materiali Cosentino utilizzati in questo progetto

Soke

Soke

Dekton

Casi di studio correlati

Numero immagine 207 della sezione corrente di Vitanya Tower di Cosentino Italia

Vuoi conoscere le soluzioni di Dekton per le facciate?

Numero immagine 208 della sezione corrente di AEC Illuminazione di Cosentino Italia

AEC Illuminazione

Case Study

Sostenibilità in grande formato presso il nuovo Technological Center AEC Illuminazione

Di SBGA Blengini Ghirardelli

Numero immagine 209 della sezione corrente di AEC Illuminazione di Cosentino Italia

Sede

Castelnuovo, Arezzo, Italia

Materiale

Dekton

Colore

Domoos

Quantità

1,100 m2

Architettura / Progetto

SBGA Blengini Ghirardelli Associati CTS e Lamec srl (allestitore)

Applicazione

Facciata ventilata

Data di fine

2021

Spessore

12 mm

Edificio passivo di grandi dimensioni

L’Innovation Technological Center (ITC) è un edificio di nuova costruzione situato all’interno della sede di AEC Illuminazione, dove vengono svolti lavori di ricerca e sviluppo. L’edificio ha una superficie di 26.500 m2 ed è stato progettato dallo studio di architettura milanese SBGA Blengini Ghirardelli, che ha basato il suo design su linee geometriche pure e semplici. Il cuore del progetto, noto come “The Lab”, è costituito dall’intersezione di due parallelepipedi in cui, su un’area di 3.000 m2, tecnici e ricercatori lavorano insieme in uno spazio pensato per favorire la collaborazione.

Una delle caratteristiche più accattivanti di questo progetto è la sua facciata nord. Questa facciata, realizzata in lastre Dekton Domoos di grande formato e con una superficie di 1.100 m2, è una delle più grandi facciate Dekton in Europa. Il rivestimento è stato installato sulla facciata ventilata utilizzando un sistema di ancoraggio fisso Keil. La scelta del materiale si è basata sui criteri di sostenibilità dell’azienda ed è stata finalizzata a isolare l’edificio dalle alte temperature.

Dekton Domoos è una finitura della Solid Collection. È una sfumatura scura, quasi nera, disponibile in lastre nel grande formato (320cm x 144cm), ideale per esterni e grandi superfici e perfetta per una facciata ventilata.

In linea con la filosofia dell’azienda

L’edificio ITC è il miglior esempio della filosofia di innovazione e automazione di AEC. La visione aziendale e le decisioni di investimento di AEC cercano continuamente soluzioni innovative per l’illuminazione degli spazi pubblici. L’edificio crea un interessante rapporto tra esterni e interni. Il paesaggio esterno funge da ispirazione per creare un’atmosfera rilassante. L’ingresso a doppia altezza e la facciata in vetro offrono uno spazio pieno di luce dove prevale la luce naturale. Tutto è stato progettato tenendo presente il benessere dei dipendenti e nulla qui ricorda un concetto tradizionale di fabbrica.

The building was built on three levels. On the ground and first floors, where tests and experiments are carried out under extreme environmental conditions, a series of double and triple height laboratories were set up from the mezzanine floor, from which it is possible to safely monitor the tests. The research offices are on the third floor. The clean, geometric lines continue on this floor. The building is completed by a skylight roof that brings light into the centre of the workspace. The technical systems and photovoltaic panels are located above the roof, concealed by a cornice, rounding off the project.

I materiali più innovativi e sostenibili combinati con un’architettura all’avanguardia si sono uniti per creare l’ITC, che è diventato il miglior biglietto da visita di AEC.

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

“Abbiamo scelto Dekton Domoos per la facciata nord perché è un materiale tecnologico, resistente e sostenibile, in grado di proteggere l’edificio”

SBGA Blengini Ghirardelli Associati

Materiali Cosentino utilizzati in questo progetto

Domoos-dektonpng-1

Domoos

Dekton
Numero immagine 234 della sezione corrente di AEC Illuminazione di Cosentino Italia

Vuoi conoscere le soluzioni di Dekton per le facciate?

Numero immagine 235 della sezione corrente di Busted Store di Cosentino Italia

Busted Store

Case Study

A timeless façade for a fashionable look

By Morten Thomsen

Numero immagine 236 della sezione corrente di Busted Store di Cosentino Italia

Sede

Silkeborg, Denmark

Materiale

Dekton

Colore

Danae

Applicazione

Glued façade

Architettura / Progetto

Morten Thomsen

Data di fine

2020

Spessore

8mm

The shop “Busted” gets a new look

Busted is a fashion shop for young people located in the main shopping area of Silkeborg, in northern Denmark. The shop needed an update to attract a younger and more demanding clientele. During this refurb process, both the façade and the shop window played a key role in attracting customers to the shop.

Busted's owners commissioned architect Morten Thomsen, founder of MMe Byg Aps, to undertake the renovation and interior design project. Thomsen invested time in researching different cladding solutions that could radically change the Busted façade. In his search, he had the good fortune to come across Cosentino's Project Manager for the region, who introduced him to the Dekton brand and its countless benefits for façade applications.

Morten was impressed with the 8mm thick slabs, which allow for on-site handling and processing, as well as the use of an invisible adhesive for fixing.

You can’t go wrong with Dekton Danae

MMe Byg Aps studio wanted a colour that would appeal to Busted’s target customers: women with a youthful, casual style, and within a fairly broad age range. From the very beginning, Dekton Danae was a favourite finish because of its brightness and timeless character. Its availability in large format slabs- 320 x 144 cm - and in two textures - grip and matt - were two highly valued aspects in the final choice. After all, it is not for nothing that this is one of Cosentino’s best sellers.

The new Busted shop, which opened in spring 2021, now looks spectacular on one of Silkeborg's most popular shopping streets. Long-time customers are delighted with the change and, more importantly, the new look is attracting a new clientele who had never thought of coming.

The renovation of the Busted shop is yet another example of the importance of design in public spaces in commercial terms. It also illustrates how quickly the investment is recouped when the project is well planned and you work with a partner like Cosentino.

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

Hai bisogno di aiuto con il tuo progetto?

Contatta i nostri specialisti per una consulenza

“The advantages of using Dekton in commercial premises are clear: the versatility of formats and its very thin thickness make it easy to design and install”
Morten Thomsen

Morten Thomsen

Architetto

Materiali Cosentino utilizzati in questo progetto

danae-dekton

Danae

Dekton

Casi di studio correlati

Numero immagine 257 della sezione corrente di Busted Store di Cosentino Italia

Vuoi conoscere le soluzioni di Dekton per le facciate?